Kyocera KM-2560 Service Manual Download Page 52 | Manualshive

Page: 52 / 392

background image

2H0/2HZ

1-3-16

U021

Initializing counters and mode settings
Description

Initializes all settings, except those pertinent to the type of machine, namely each counter, service call history
and mode setting. Also initializes backup RAM according to region specification selected in maintenance item
U252 Setting the destination.
Refer to *2 of the maintenance mode item list about the item initialized.

Purpose

To return the machine settings to their factory default.

Method

1. Press the start key.
2. Press [EXECUTE] on the touch panel.
3. Press the start key. All data other than that for adjustments due to variations between machines is initial-

ized based on the destination setting.

4. Turn the main power switch off and on.

An error code is displayed in case of an intialization error. Refer to the table of the error codes on P.1-3-15.
When ERROR 09 occurred, turn main power switch off then on, format the hard disk using maintenance
item U024, and execute initialization using maintenance item U021. For other errors occurred, turn main
power switch off then on, and execute initialization using maintenance item U021.

U022

Initializing backup memory
Description

Initializes only the backup data for image processing.
Also, initializes the settings with the system menu in order to restore default settings simultaneously when
[MAIN+ENGINE] is selected.
Reregister the fax settings since the settings are initialized when the fax kit is installed.

Purpose

To be executed as required.

Caution

Run the maintenance item U411 (Adjusting the scanner automatically) after initialization the backup data of
scanner or DP main PWB (see page 1-3-68).

Method

1. Press the start key.
2. Select the item to initialize.

3. When selecting [MAIN+ENGINE], select the destination.

4. Press the start key. All data in the backup RAM is initialized.
5. Turn the main power switch off and on.

An error code is displayed in case of an intialization error. Refer to the table of the error codes on P.1-3-15.
When ERROR 09 occurred, turn main power switch off then on, format the hard disk using maintenance
item U024, and execute initialization using maintenance item U022. For other errors occurred, turn main
power switch off then on, and execute initialization using maintenance item U022.

Maintenance

item No.

Description

Display

Description

MAIN+ENGINE

Initialize the backup data of main PWB and engine PWB.

SCANNER

Initialize the backup data of scanner.

DP

Initialize the backup data of DP main PWB.

Display

Description

INCH

Inch (North America) specifications

EUROPE METRIC

Metric (Europe) specifications

ASIA PACIFIC

Metric (Asia Pacific) specifications

«
...
50
51
52
53
54
...
»

Summary of Contents for KM-2560









































































































































































































































































































































































































Reviews:

No comments

Related manuals for KM-2560

image Prograf iPF785 Series

Brand: Canon Pages: 136

Brand: GBC Pages: 110

ImageCLASS MF4570dw

Brand: Canon Pages: 164

imagePRESS C800 Series

Brand: Canon Pages: 132

ImageCLASS MF5730

Brand: Canon Pages: 2

WorkCentre 4265

Brand: Xerox Pages: 20

Brand: Xerox Pages: 11

4150S - WorkCentre B/W Laser

Brand: Xerox Pages: 4

Brand: imagistics Pages: 57

3600DN - Phaser B/W Laser Printer

Brand: Xerox Pages: 2

Brand: Oki Pages: 180

Brand: Kyocera Pages: 13

Brand: AstroJet Pages: 97

Brand: MAC TOOLS Pages: 2

Brand: U-Line Pages: 18

Brand: Oki Pages: 182

Brand: Source Technologies Pages: 47

Brand: Sagem Pages: 154

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands