manualshive.com logo in svg

Kyocera KM-2560, Service Manual

The Kyocera KM-2560 is a high-performance multifunctional printer designed for office use. With its advanced features and efficient functionality, this product delivers exceptional quality prints, copies, and scans. To access the Service Manual and user manual for free, you can conveniently download them from manualshive.com.

Share
Download
background image

2H0/2HZ

1-4-42

(15)
A paper jam in the 
paper feed, paper 
conveying, fuser, 
eject or duplex sec-
tion is indicated when 
the main power 
switch is turned on.

1. A piece of paper torn 

from copy paper is 
caught around feed 
switch 1/2/3, registration 
switch, feedshift switch, 
eject switch or duplex 
paper conveying switch.

Check visually and remove it, if any.

2. Defective feed switch 1/

2/3, registration switch, 
feedshift switch, eject 
switch or duplex paper 
conveying switch.

Run maintenance item U031 and turn each switch on and off 
manually. Replace the switch if indication of the corresponding 
switch on the touch panel is not displayed in reverse.

(16)
The message 
requesting cover to 
be closed is dis-
played when the front 
cover or left cover 1/2 
is closed.

1. Poor contact in the con-

nector terminals of safety 
switch 1/2 or left cover 2 
switch.

Reinsert the connector. Also check for continuity within the con-
nector cable. If none, remedy or replace the cable.

2. Defective safety switch 1/

2 or left cover 2 switch.

Check for continuity across each switch. If there is no continuity 
when the switch is on, replace it.

(17)
Others.

1. Wiring is broken, shorted 

or makes poor contact.

Check for continuity. If none, repair.

Problem

Causes

Check procedures/corrective measures

Summary of Contents for KM-2560









































































































































































































































































































































































































Reviews:

No comments

Related manuals for KM-2560

NEC 870 - SuperScript B/W Laser Printer Network User'S Manual preview
870 - SuperScript B/W Laser Printer
Brand: NEC Pages: 52
NEC SuperScript 1800 Quick Start Manual preview
SuperScript 1800
Brand: NEC Pages: 8
DASCO EBS-260 Cleaning Procedure preview
EBS-260
Brand: DASCO Pages: 2
NEC Pinwriter P6 Specification preview
Pinwriter P6
Brand: NEC Pages: 10
EBS Ink-Jet Systems Hi-Res EBS-2600 Manual preview
Hi-Res EBS-2600
Brand: EBS Ink-Jet Systems Pages: 3
Ricoh Aficio SP C240SF Firmware Update Manual preview
Aficio SP C240SF
Brand: Ricoh Pages: 14
Glunz & Jensen NewsWriter XL Operating Manual preview
NewsWriter XL
Brand: Glunz & Jensen Pages: 104
Lanier 5622 AG Operator'S Manual preview
5622 AG
Brand: Lanier Pages: 118
Brady BradyPrinter A5500 User Manual preview
BradyPrinter A5500
Brand: Brady Pages: 72
Wasp WPL206 Series User Manual preview
WPL206 Series
Brand: Wasp Pages: 46
Kyocera ECOSYS M3860idn Operation Manual preview
ECOSYS M3860idn
Brand: Kyocera Pages: 483
Epson Stylus CX1500 Notices And Warranty preview
Stylus CX1500
Brand: Epson Pages: 24
Epson Stylus CX3200 Specifications preview
Stylus CX3200
Brand: Epson Pages: 2
Epson Stylus CX3500 Series Brochure & Specs preview
Stylus CX3500 Series
Brand: Epson Pages: 4
Epson STYLUS CX3700 SERIES Brochure & Specs preview
STYLUS CX3700 SERIES
Brand: Epson Pages: 4
Epson Stylus CX3200 Copy Manual preview
Stylus CX3200
Brand: Epson Pages: 60
Epson Stylus CX3100 Service Manual preview
Stylus CX3100
Brand: Epson Pages: 90
Epson Stylus CX3500 Series Quick Reference Manual preview
Stylus CX3500 Series
Brand: Epson Pages: 101

Brands by name

Popular brands

Load more brands