manualshive.com logo in svg

Kyocera KM-2560, Service Manual

The Kyocera KM-2560 is a high-performance multifunctional printer designed for office use. With its advanced features and efficient functionality, this product delivers exceptional quality prints, copies, and scans. To access the Service Manual and user manual for free, you can conveniently download them from manualshive.com.

Share
Download
background image

2H0/2HZ

1-3-45

U135

Checking toner motor operation
Description

Turns the toner feed motor and toner feed clutch on.

Purpose

To check the operation of the toner feed motor or toner feed clutch. Settings may also be modified where 
mobility in toner is inferior or when printing materials of very high density. Normally no change is necessary 
from the initial setting.

Method

1. Press the start key.
2. Select the item.

Method

1. Select [TONER CARRY] or [TONER SUPPLY].
2. Press the start key. The operation starts.
3. To stop operation, press the stop key.

Setting: Low toner mobility

1. Select [CARRY ON TIME].
2. Increasing the setting value using the + key.
3. Press the start key. The value is set.

Setting: Printing very high density materials

1. Select [SUPPLY ON TIME].
2. Increasing the setting value using the + key.
3. Press the start key. The value is set.

Completion 

Press the stop key. The screen for selecting a maintenance item No. is displayed.

Maintenance

item No.

Description

Display

Description

Setting 
range

Initial 
setting

TONER CARRY

Toner feed motor (TFM)

-

-

TONER SUPPLY

Toner feed clutch (TNFCL)

-

-

CARRY ON TIME

Toner feed motor drive on time

0 to 255

100

SUPPLY ON TIME

Toner feed clutch on time

0 to 255

30

SUPPLY OFF TIME

Toner feed clutch off time

0 to 255

100

Summary of Contents for KM-2560









































































































































































































































































































































































































Reviews:

No comments

Related manuals for KM-2560

DataCard CR500 Quick Install Manual preview
CR500
Brand: DataCard Pages: 17
DataCard CR500 User Reference Manual preview
CR500
Brand: DataCard Pages: 24
Samsung SPP 2020 - Photo Printer - 20 Sheets Manual Del Usuario preview
SPP 2020 - Photo Printer - 20 Sheets
Brand: Samsung Pages: 81
Samsung ML-6000 Bedienungsanleitung preview
ML-6000
Brand: Samsung Pages: 98
Samsung ML-4050N Compatibility Manual preview
ML-4050N
Brand: Samsung Pages: 6
Samsung ML-3750ND User Manual preview
ML-3750ND
Brand: Samsung Pages: 203
Samsung ML-3312ND Manual Del Usuario preview
ML-3312ND
Brand: Samsung Pages: 264
Samsung ML-2165W/XAA Manual Del Usuario preview
ML-2165W/XAA
Brand: Samsung Pages: 228
Samsung ML-2165 User Manual preview
ML-2165
Brand: Samsung Pages: 211
Samsung ML-2525 Brochure & Specs preview
ML-2525
Brand: Samsung Pages: 5
Samsung ML-1865W Manual Del Usuario preview
ML-1865W
Brand: Samsung Pages: 92
Samsung ML-1865W User Manual preview
ML-1865W
Brand: Samsung Pages: 75
Samsung ML-6060 Technical Instructions preview
ML-6060
Brand: Samsung Pages: 11
Samsung ML-1450 Series Manual Del Usuario preview
ML-1450 Series
Brand: Samsung Pages: 206
Samsung ML 3050 - B/W Laser Printer Manual Del Usuario preview
ML 3050 - B/W Laser Printer
Brand: Samsung Pages: 103
Samsung ML 3050 - B/W Laser Printer User Manual preview
ML 3050 - B/W Laser Printer
Brand: Samsung Pages: 215
Samsung ML-1450 Series Quick Manual preview
ML-1450 Series
Brand: Samsung Pages: 2
Samsung CLP 510N - Color Laser Printer User Manual preview
CLP 510N - Color Laser Printer
Brand: Samsung Pages: 266

Brands by name

Popular brands

Load more brands