manualshive.com logo in svg

Kyocera KM-2560, Service Manual

The Kyocera KM-2560 is a high-performance multifunctional printer designed for office use. With its advanced features and efficient functionality, this product delivers exceptional quality prints, copies, and scans. To access the Service Manual and user manual for free, you can conveniently download them from manualshive.com.

Share
Download
background image

2H0/2HZ

1-4-29

C8190

Finisher trailing edge registration 
motor problem (optional built-in fin-
isher)

When the trailing edge registration 
home-position sensor is turned on during 
initialization, the sensor did not turn on 
while it has moved by 106 pulses.
When the trailing edge registration 
home-position sensor is turned off during 
initialization, the sensor did not turn on in 
3 s.

The trailing edge 
registration motor 
connector makes 
poor contact.

Reinsert the connector. Also check for conti-
nuity within the connector cable. If none, 
remedy or replace the cable.

Defective trailing 
edge registration 
motor.

Replace trailing edge registration motor. 

The trailing edge 
registration home 
position sensor 
connector makes 
poor contact.

Reinsert the connector. Also check for conti-
nuity within the connector cable. If none, 
remedy or replace the cable.

Defective trailing 
edge registration 
home position sen-
sor.

Replace the trailing edge registration home 
position sensor.

Defective finisher 
control PWB.

Replace the finisher control PWB and check 
for correct operation.

C8210

Stapler problem (optional document 
finisher)

When the stapler motor is driving, the 
ON status of the stapler home position 
sensor cannot be detected even if a 
specified time has elapsed.

The stapler con-
nector makes poor 
contact.

Reinsert the connector. Also check for conti-
nuity within the connector cable. If none, 
remedy or replace the cable.

The stapler is 
blocked with a sta-
ple.

Remove the stapler cartridge, and check the 
cartridge and the stapling section of the sta-
pler.

The stapler is bro-
ken.

Replace the stapler and check for correct 
operation.

Defective finisher 
main PWB.

Replace the finisher main PWB and check 
for correct operation.

Finisher stapler problem (optional 
built-in finisher)

The stapler home position sensor does 
not change state from nondetection to 
detection within 200 ms of the start of 
stapler motor counterclockwise (forward) 
rotation.
During initialization, the stapler home 
position sensor does not change state 
from non-detection to detection within 
600 ms of the start of stapler motor 
clockwise (reverse) rotation.

The stapler con-
nector makes poor 
contact.

Reinsert the connector. Also check for conti-
nuity within the connector cable. If none, 
remedy or replace the cable.

The stapler is 
blocked with a sta-
ple.

Remove the stapler cartridge, and check the 
cartridge and the stapling section of the sta-
pler.

The stapler is bro-
ken.

Replace the front stapler and check for cor-
rect operation.

Defective finisher 
control PWB.

Replace the finisher control PWB and check 
for correct operation.

Code

Contents

Remarks

Causes

Check procedures/corrective measures

Summary of Contents for KM-2560









































































































































































































































































































































































































Reviews:

No comments

Related manuals for KM-2560

Canon iR3245 Troubleshooting Manual preview
iR3245
Brand: Canon Pages: 300
Canon iR3245 Network Manual preview
iR3245
Brand: Canon Pages: 288
Canon iR3245 User Manual preview
iR3245
Brand: Canon Pages: 58
Canon iR1510 Quick Start Manual preview
iR1510
Brand: Canon Pages: 30
Ier I420 User Safety And Start Manual preview
I420
Brand: Ier Pages: 8
Samsung M267x series Quick Installation Manual preview
M267x series
Brand: Samsung Pages: 2
Samsung CLX-6220FX Quick Install Manual preview
CLX-6220FX
Brand: Samsung Pages: 2
Samsung CLX-3305FW Manual Del Usuario preview
CLX-3305FW
Brand: Samsung Pages: 341
Samsung CLX-3170 Quick Install Manual preview
CLX-3170
Brand: Samsung Pages: 8
Samsung CLX2160N - Color Laser - All-in-One Manual Del Usuario preview
CLX2160N - Color Laser - All-in-One
Brand: Samsung Pages: 118
Samsung CLX 3160FN - Color Laser - All-in-One Manual Del Usuario preview
CLX 3160FN - Color Laser - All-in-One
Brand: Samsung Pages: 142
Samsung CLP-770ND - Color Laser Printer Quick Install Manual preview
CLP-770ND - Color Laser Printer
Brand: Samsung Pages: 2
Samsung CLP 610ND - Color Laser Printer Manual Del Usuario preview
CLP 610ND - Color Laser Printer
Brand: Samsung Pages: 114
Samsung CLP 500 Instructions Manual preview
CLP 500
Brand: Samsung Pages: 6
Samsung CLP 500 Paigaldusjuhend preview
CLP 500
Brand: Samsung Pages: 15
Samsung CLP 600N - Color Laser Printer User Manual preview
CLP 600N - Color Laser Printer
Brand: Samsung Pages: 227
Samsung CLP 600N - Color Laser Printer Manual Del Usuario preview
CLP 600N - Color Laser Printer
Brand: Samsung Pages: 118
Samsung CLP 300N - Network-ready Color Laser Printer Manual De Usuario preview
CLP 300N - Network-ready Color Laser Printer
Brand: Samsung Pages: 94

Brands by name

Popular brands

Load more brands