manualshive.com logo in svg

Kyocera KM-2560, Service Manual

The Kyocera KM-2560 is a high-performance multifunctional printer designed for office use. With its advanced features and efficient functionality, this product delivers exceptional quality prints, copies, and scans. To access the Service Manual and user manual for free, you can conveniently download them from manualshive.com.

Share
Download
background image

2H0/2HZ

1-4-16

(28)
A paper jam in 
optional document 
finisher is indicated 
during copying (eject 
sensor stay jam).
Jam code 83

Built-in finisher

Defective paper conveying 
switch.

With 5 V DC present at YC2-23 on the finisher control PWB, 
check if YC2-21 on the finisher control PWB remains low when 
the paper conveying switch is turned on and off. If it does, replace 
the paper conveying switch.

Check if the eject roller or 
eject pulley is deformed.

Check and remedy.

(29)
A paper jam in 
optional document 
finisher is indicated 
during copying (eject 
sensor non-arrival 
jam).
Jam code 92

Defective eject sensor.

With 5 V DC present at CN5-4 on the finisher main PWB, check if 
CN5-6 on the finisher main PWB remains low or high when the 
eject sensor is turned on and off. If it does, replace the eject sen-
sor.

Check if the paper convey-
ing motor malfunctions.

Check.

Check if the eject roller and 
eject pulley contact each 
other.

Check and remedy.

Check if the eject guide is 
deformed.

Check and remedy.

Defective finisher main 
PWB.

Replace the finisher main PWB and check for correct operation.

(30)
A paper jam in 
optional document 
finisher is indicated 
during copying 
(reverse sensor jam).
Jam code 93

Defective reverse sensor.

With 5 V DC present at CN14-5 on the finisher main PWB, check 
if CN14-7 on the finisher main PWB remains low or high when the 
reverse sensor is turned on and off. If it does, replace the reverse 
sensor.

Check if the reverse motor 
malfunctions.

Check.

Check if the reverse roller 
and reverse pulley contact 
each other.

Check and remedy.

Check if the reverse guide 
is deformed.

Check and remedy.

Defective finisher main 
PWB.

Replace the finisher main PWB and check for correct operation.

(31)
A paper jam in 
optional document 
finisher is indicated 
during copying 
(paper entry sensor 
stay jam).
Jam code 94

Extremely curled paper.

Change the paper.

Defective paper entry sen-
sor.

With 5 V DC present at CN14-1and CN14-3 on the finisher main 
PWB, check if CN14-2 and CN14-4 on the main PCB remains low 
or high when the paper entry sensor is turned on and off. If it does, 
replace the paper entry sensor.

Check if the paper entry 
guide is deformed.

Check and remedy.

Defective finisher main 
PWB.

Replace the finisher main PWB and check for correct operation.

Problem

Causes/check procedures

Corrective measures

Summary of Contents for KM-2560









































































































































































































































































































































































































Reviews:

No comments

Related manuals for KM-2560

Samsung CLP-36 Series Manual preview
CLP-36 Series
Brand: Samsung Pages: 9
Samsung Bixolon SRP-500 Command Manual preview
Bixolon SRP-500
Brand: Samsung Pages: 27
Samsung 550N - CLP Color Laser Printer User Manual preview
550N - CLP Color Laser Printer
Brand: Samsung Pages: 288
Samsung 2 COLOR THERMAL PRINTER SRP-275 Quick Reference Manual preview
2 COLOR THERMAL PRINTER SRP-275
Brand: Samsung Pages: 8
Samsung CLP-300 Brochure & Specs preview
CLP-300
Brand: Samsung Pages: 6
Samsung CLP-300 User Manual preview
CLP-300
Brand: Samsung Pages: 91
Canon imageRUNNER ADVANCE C350iF Service Manual preview
imageRUNNER ADVANCE C350iF
Brand: Canon Pages: 102
Canon imageRUNNER ADVANCE C2230 Manual preview
imageRUNNER ADVANCE C2230
Brand: Canon Pages: 12
Canon IR 2420 User Manual preview
IR 2420
Brand: Canon Pages: 598
Wang System 2200 2231w-3 User Manual preview
System 2200 2231w-3
Brand: Wang Pages: 52
Kyocera Ecosys FS-C5300DN Operation Manual preview
Ecosys FS-C5300DN
Brand: Kyocera Pages: 35
Xerox DocuPrint 96 IPS Series System Overview Manual preview
DocuPrint 96 IPS Series
Brand: Xerox Pages: 101
Ricoh IM C6500 Operating Instructions Manual preview
IM C6500
Brand: Ricoh Pages: 24
Oce TDS450 Student Manual preview
TDS450
Brand: Oce Pages: 62
EcLine EC-PM-80320D User Manual preview
EC-PM-80320D
Brand: EcLine Pages: 72
Ricoh Aficio AP3800C Setup Manual preview
Aficio AP3800C
Brand: Ricoh Pages: 84
Canon MAXIFY MB2350 Online Manual preview
MAXIFY MB2350
Brand: Canon Pages: 1154
Oki ML3310e Setup Manual preview
ML3310e
Brand: Oki Pages: 23

Brands by name

Popular brands

Load more brands