Kyocera KM-2560 Service Manual Download Page 48 | Manualshive

Page: 48 / 392

background image

2H0/2HZ

1-3-12

U000

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

U001

Exiting the maintenance mode
Description

Exits the maintenance mode and returns to the normal copy mode.

Purpose

To exit the maintenance mode.

Method

Press the start key. The normal copy mode is entered.

U002

Setting the factory default data
Description

Restores the machine conditions to the factory default settings.

Purpose

To move the mirror frame of the scanner to the position for transport (position in which the frame can be fixed).

Method

1. Press the start key.
2. Press [MODE1(ALL)] on the touch panel.
3. Press the start key.

The mirror frame of the scanner returns to the position for transport.

4. Turn the main power switch off and on.

An error code is displayed in case of an intialization error. Refer to the table of the error codes on P.1-3-15.
When ERROR 09 occurred, turn main power switch off then on, format the hard disk using maintenance
item U024, and execute initialization using maintenance item U002. For other errors occurred, turn main
power switch off then on, and execute initialization using maintenance item U002.

Maintenance

item No.

Description

No.

Description

Supplement

(29)

Identification name for the security kit

(30)

Security kit version

(31)

Printed page counts

Total/Copy/Printer/Fax

(32)

Scanned page counts

Total/Copy/Other

(33)

Counts by paper sizes

(34)

Fax kit information

This item is printed only when the fax kit is installed.

(35)

Destination information/Area informa-
tion

(36)

Printable area setting

(37)

Top offset for each bin

MP tray/Cassette 2/Cassette 3/Cassette 4

(38)

Left offset for each bin

MP tray/Cassette 2/Cassette 3/Cassette 4

(39)

Margin/Page length/Page width
settings

Top margin integer part/Top margin decimal part/
Left margin integer part/Left margin decimal part/
Page length integer part/Page length decimal part/
Page width integer part/Page width decimal part

(40)

Panel lock information/USB information Panel lock

0: OFF/1: Partial lock/2: Full lock
USB
0: Not installed/1: Full speed/2: Hi speed

(41)

RFID information

(42)

Maintenance information

«
...
46
47
48
49
50
...
»

Summary of Contents for KM-2560









































































































































































































































































































































































































Reviews:

No comments

Related manuals for KM-2560

Brand: Xerox Pages: 108

Brand: Datamax Pages: 2

Brand: Canon Pages: 4

PIXMA MG3220 series

Brand: Canon Pages: 4

Brand: Canon Pages: 22

Pixma G3020 Series

Brand: Canon Pages: 34

Pixma MG3500 Series

Brand: Canon Pages: 3

Pixma MG7100 Series

Brand: Canon Pages: 4

PIXMA G7000 Series

Brand: Canon Pages: 16

Brand: Canon Pages: 10

Brand: Canon Pages: 4

Brand: Canon Pages: 132

Brand: Canon Pages: 62

MF3110 - ImageCLASS Laser Multifunction

Brand: Canon Pages: 2

PIXMA MG3220 series

Brand: Canon Pages: 7

Brand: Canon Pages: 2

Brand: Canon Pages: 34

Brand: Oki Pages: 104

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands