manualshive.com logo in svg

Kyocera KM-2560, Service Manual

The Kyocera KM-2560 is a high-performance multifunctional printer designed for office use. With its advanced features and efficient functionality, this product delivers exceptional quality prints, copies, and scans. To access the Service Manual and user manual for free, you can conveniently download them from manualshive.com.

Share
Download
background image

2H0/2HZ

1-2-10

1. Connect the power cord to the connector on the machine.
2. Insert the power plug into the wall outlet.

1. Turn the main power switch on. Toner installation is started.
2. The drive chain is disengaged when toner installation is completed.

Run maintenance mode U130 if [Add Toner] remains displayed even after the drive chain is disengaged.

1. Press the status key.
2. Enter the maintenance mode by entering 10871087 using the numeric keys.
3. Enter 000 using the numeric keys and press the start key.
4. Select MAINTENANCE and press the start key to output a list of the current settings of the maintenance items.
5. Press the stop key.

1. Enter 001 using the numeric keys and press the start key. The machine exits the maintenance mode.

1. Select [Report Print] to output the user various setting reports.

1. Place an original and make test copies.

1. According to need, attach the correspond language label.

Connect the power cord.

Installing toner.

Output an own-status report (maintenance item U000).

Exit maintenance mode.

Print out the user setting list.

Make test copies.

Attaching the language label (230 V specifications only).

Completion of the machine installation.

Summary of Contents for KM-2560









































































































































































































































































































































































































Reviews:

No comments

Related manuals for KM-2560

Chamiin I&C 0024-1236 Operation & Maintenance Instructions Manual preview
0024-1236
Brand: Chamiin I&C Pages: 18
Xerox WorkCentre 7655 Evaluator Manual preview
WorkCentre 7655
Brand: Xerox Pages: 24
Kyocera KM-1635 Service Manual preview
KM-1635
Brand: Kyocera Pages: 13
Kyocera KM-1820 Quick Start Manual preview
KM-1820
Brand: Kyocera Pages: 2
Wang System 2200 2231w-3 User Manual preview
System 2200 2231w-3
Brand: Wang Pages: 52
Xerox 8200DX - Phaser Color Solid Ink Printer Manual preview
8200DX - Phaser Color Solid Ink Printer
Brand: Xerox Pages: 2
Kyocera ECOSYS P8060cdn Quick Manual preview
ECOSYS P8060cdn
Brand: Kyocera Pages: 20
Brother Industries DCP-T520W Online User'S Manual preview
DCP-T520W
Brand: Brother Industries Pages: 501
WOOSIM WSP-CP Operating Manual preview
WSP-CP
Brand: WOOSIM Pages: 20
Canon iR ADVANCE C5035i Series Manual preview
iR ADVANCE C5035i Series
Brand: Canon Pages: 2
Canon iR 3100C User Manual preview
iR 3100C
Brand: Canon Pages: 80
Canon iR C6800 Series Portable Manual preview
iR C6800 Series
Brand: Canon Pages: 456
Canon iR C3200 Series Portable Manual preview
iR C3200 Series
Brand: Canon Pages: 170
Canon iR C2880 series Service Manual preview
iR C2880 series
Brand: Canon Pages: 610
Canon iR C3200 Series Service Manual preview
iR C3200 Series
Brand: Canon Pages: 1216
Canon iR C6800 Series Service Manual preview
iR C6800 Series
Brand: Canon Pages: 1404
DataCard 7000 Datasheet preview
7000
Brand: DataCard Pages: 2
DataCard 295 Specifications preview
295
Brand: DataCard Pages: 2

Brands by name

Popular brands

Load more brands