JBT FoodTech Frigoscandia GYRoCOMPACT M7 Installation Manual Download

Page: 247 / 288

163

1000-06-01GB-10-11

CORRECTIVE MAINTENANCE

Splicing the conveyor belt

1. Pull the two conveyor belt ends together.
2. Align the side links with the rod holes cen-

tred opposite each other.

3. Align the mesh (B), see illustration.
4. Start from under the side links on any side,

thread the rod (A) through the complete

mesh and through both side links on the

opposite side. Push the rod 30 mm past the

link foot.

5. Push the rod and mesh up, in line with the

holes in the side links, and hammer the rod

back through the side links on the start side.

Note!

•

Make sure no link feet has been bent.

•

Make sure the washer at each end of the

mesh is in place.

•

Make sure the mesh is in correct position.

•

Make sure the rod is centred between the

side link feet.

Before welding the conveyor belt

1. Disconnect the frequency converter.

Always do this despite of other

recommendations!

2. Make sure the link foot to be welded do not

have contact with the glide strip.

3. Make sure the earth clamp (F) is placed on

the link to be welded.

4. Position the side links (D) in line with the

rest of the conveyor belt.

Note!

Make sure the side links (D) are straight on both

sides before welding.

Mesh in wrong position Mesh in correct position

Summary of Contents for FoodTech Frigoscandia GYRoCOMPACT M7
































































































































































































































































































Search results

Summary of Contents for FoodTech Frigoscandia GYRoCOMPACT M7

Reviews:

Related manuals for FoodTech Frigoscandia GYRoCOMPACT M7

Brands by name

Popular brands

JBT FoodTech Frigoscandia GYRoCOMPACT M7, Installation Manual

Search results

Summary of Contents for FoodTech Frigoscandia GYRoCOMPACT M7

Reviews:

Related manuals for FoodTech Frigoscandia GYRoCOMPACT M7

Brands by name

Popular brands