manualshive.com logo in svg

Infineon Technologies XC161, User Manual

Share
Download
Infineon Technologies XC161 User Manual Download Page 53

XC161 Derivatives

Peripheral Units (Vol. 2 of 2)

The General Purpose Timer Units

 

User’s Manual

14-39

V2.2, 2004-01

GPT_X1, V2.0

14.2.3

GPT2 Auxiliary Timer T5 Control 

Auxiliary timer T5 can be configured for timer mode, gated timer mode, or counter mode
with the same options for the timer frequencies and the count signal as the core timer
T6. In addition to these 3 counting modes, the auxiliary timer can be concatenated with
the core timer. The contents of T5 may be captured to register CAPREL upon an external
or an internal trigger. The start/stop function of the auxiliary timers can be remotely
controlled by the T6 run control bit. Several timers may thus be controlled synchronously.

The current contents of the auxiliary timer are reflected by its count register T5. This
register can also be written to by the CPU, for example, to set the initial start value.

The individual configurations for timer T5 are determined by its bitaddressable control
register T5CON. Some bits in this register also control the function of the CAPREL
register. Note that functions which are present in all timers of block GPT2 are controlled
in the same bit positions and in the same manner in each of the specific control registers.

Note: The auxiliary timer has no output toggle latch and no alternate output function.

GPT12E_T5CON 
Timer 5 Control Register

SFR (FF46

H

/A3

H

)

Reset Value: 0000

H

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

T5

SC

T5

CLR

CI

T5

CC

CT3

T5

RC

-

T5

UD

T5R

T5M

T5I

rw

rw

rw

rw

rw

rw

-

rw

rw

rw

rw

Field

Bits

Typ

Description

T5SC

15

rw

Timer 5 Capture Mode Enable
0

Capture into register CAPREL Disabled

1

Capture into register CAPREL Enabled

T5CLR

14

rw

Timer T5 Clear Enable Bit
0

Timer T5 is not cleared on a capture event

1

Timer T5 is cleared on a capture event

CI

[13:12] rw

Register CAPREL Capture Trigger Selection
(depending on bit CT3)
00

Capture disabled

01

Positive transition (rising edge) on CAPIN or 
any transition on T3IN

10

Negative transition (falling edge) on CAPIN or 
any transition on T3EUD

11

Any transition (rising or falling edge) on CAPIN 
or any transition on T3IN or T3EUD

Summary of Contents for XC161




































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands