manualshive.com logo in svg

Infineon Technologies XC161, User Manual

Share
Download
Infineon Technologies XC161 User Manual Download Page 224

 

XC161 Derivatives

Peripheral Units (Vol. 2 of 2)

IIC-Bus Module

User’s Manual

20-6

V2.2, 2004-01

IIC_X, V2.0

ACKDIS

5

rwh

Acknowledge Pulse Disable
0

An acknowledge pulse is generated for each 
received byte

1

No acknowledge pulse is generated

Note: ACKDIS is automatically cleared by a stop

condition.

BUM

4

rwh

Busy Master
0

Clearing bit BUM immediately generates a 
stop condition

1

Setting bit BUM generates a start condition in 
(multi-) Master mode

Note: Setting bit BUM while the bus is busy (BB = 1)

generates an arbitration lost situation.
In this case, BUM is cleared and bit AL is set.
BUM cannot be set in slave mode.

MOD

[3:2]

rw

Basic Operating Mode
00

IIC module is disabled and initialized (Init-
Mode). Transmissions in progress will be 
aborted.

01

Slave mode

10

Single-Master mode

11

Multi-Master mode

RSC

1

rwh

Repeated Start Condition Trigger
0

No operation

1

Generate a repeated start condition in (multi-) 
master mode. RSC cannot be set in slave 
mode.

Note: RSC is cleared automatically after the

repeated start condition has been sent.

M10

0

rw

Slave Address Width Selection
0

7-bit slave address, using ICA[7:1]

1

10-bit slave address, using ICA[9:0]

Field

Bits

Type

Description

Summary of Contents for XC161




































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands