HP StorageWorks 2000fc Reference Manual Download Page 183 | Manualshive

Page: 183 / 330

background image

Chapter 6

Additional Configuration Functions and Utilities

183

Disabling Partner Firmware Upgrade

If a service technician tells you to disable partner firmware upgrade:

1. Select Manage > General Config > System Configuration.

2. Set Partner Firmware Upgrade to Disabled.

Changing Utility Priority

You can change the priority at which the Verify, Reconstruct, Expand, and Initialize
utilities run when there are active I/O operations competing for the system’s
controllers.

To change utility priority:

1. Select Manage > General Config > System Configuration.

2. For Utility Priority, select a priority.

3. Click Change System Configuration.

Priority Value

Description

High

Use when your highest priority is to get the system back to a fully
fault-tolerant state. This causes heavy I/O with the host to be slower
than normal. This value is the default.

Medium

Use when you want to balance data streaming with data redundancy.

Low

Use when streaming data without interruption, such as for a web
server, is more important than data redundancy. This enables the
Reconstruct or other utility to run at a slower rate with minimal
effect on host I/O.

«
...
181
182
183
184
185
...
»

Summary of Contents for StorageWorks 2000fc











































































































































































































































































































































Reviews:

No comments

Related manuals for StorageWorks 2000fc

Brand: HAGOR Pages: 8

Brand: Zonet Pages: 63

Brand: Zonet Pages: 2

Brand: CoolGear Pages: 19

Brand: Otto Bock Pages: 160

Brand: Aiphone Pages: 8

Brand: Edimax Pages: 14

Brand: Promise Technology Pages: 41

Brand: Qlogic Pages: 18

Brand: National Instruments Pages: 19

Brand: GeoVision Pages: 2

Brand: Moen Pages: 2

Brand: Digitus Pages: 48

Brand: StarTech.com Pages: 2

Redbooks ServeRAID-MR10k

Brand: IBM Pages: 3

Brand: IBM Pages: 35

Brand: IBM Pages: 18

System Storage DS4000

Brand: IBM Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands