HP StorageWorks 2000fc Reference Manual Download Page 277 | Manualshive

Page: 277 / 330

background image

Appendix E

Event Codes

277

24

Informational

The assigned LUN for this volume
has changed.

25

Informational

The statistics for the specified vdisk
have been reset.

27

Informational

Cache parameters have been changed
for the specified vdisk.

28

Informational

Controller parameters have been
changed. This event is logged when
general configuration changes are
made; for example, utility priority,
remote notification settings, user
interface passwords, and management
port IP values. This event is

not

logged when changes are made to
vdisk or volume configuration.

31

Informational

A global or vdisk spare was deleted.

32

Informational

Vdisk verification has started.

33

Informational

Controller time/date has been
changed. This event is logged before
the change happens so the event
timestamp shows the "old" time.

34

Informational

Controller has been restored to
factory defaults.

For an FC controller, restart it to
make the default loop ID take
effect.

37

Informational

Vdisk reconstruction has started.

TABLE E-1

Event Descriptions and Recommended Actions

(Continued)

Event
Code

Event Type

Description

Recommended Action

«
...
275
276
277
278
279
...
»

Summary of Contents for StorageWorks 2000fc











































































































































































































































































































































Reviews:

No comments

Related manuals for StorageWorks 2000fc

Brand: Conrad Pages: 4

Brand: NETGEAR Pages: 2

Brand: Firmtech Pages: 68

Brand: Allied Telesis Pages: 2

Brand: Velleman Pages: 18

GA511 - Gigabit Ethernet PC Card

Brand: NETGEAR Pages: 50

Brand: Proware Pages: 39

USB2-F-7 01 Series

Brand: Connective Peripherals Pages: 3

Brand: Linksys Pages: 68

Brand: D-Link Pages: 50

XE602 - Powerline Ethernet Adapter

Brand: NETGEAR Pages: 18

FOUR LINE CORDLESS ANALOG ADAPTER 2742

Brand: Cortelco Pages: 21

Brand: Linksys Pages: 2

CROSSFIRE XFF-APL

Brand: Task Force Tips Pages: 2

Brand: Quatech Pages: 52

Brand: Cool Automation Pages: 28

Brand: Expert Pages: 18

Brand: Eusso Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands