HP StorageWorks 2000fc Reference Manual Download Page 219 | Manualshive

Page: 219 / 330

background image

Chapter 7

Troubleshooting Using SMU

219

Event Severities

The storage system generates events having three severity levels:

■

Informational – A problem occurred that the system corrected, or a system
change has been made. These events are purely informational; no action required.

■

Warning – Something related to the system or to a virtual disk has a problem.
Correct the problem as soon as possible.

■

Critical – Something related to the system or to a virtual disk has failed and
requires immediate attention.

There are a number of conditions that trigger warning or critical events and can
affect the state of status LEDs.

Viewing the Event Log

Some of the key warning and error events included in the event log during operation
include the following:

■

Disk detected error

■

Disk channel error

■

Drive down

■

Virtual disk critical

■

Virtual disk offline

■

Temperature warning

■

Temperature failure (this leads to a shutdown which is also logged)

■

Voltage warning

■

Voltage failure (this leads to a shutdown which is also logged)

The event log stores the most recent events with a time stamp next to them with
one-second granularity.

Note –

If you are having a problem with the system or a virtual disk, check the

event log before calling technical support. Event messages might enable you to
resolve the problem.

You can save the event log to a file; see “Saving Log Information to a File” on
page 192.

«
...
217
218
219
220
221
...
»

Summary of Contents for StorageWorks 2000fc











































































































































































































































































































































Reviews:

No comments

Related manuals for StorageWorks 2000fc

Brand: Oki Pages: 60

Brand: Evolution Pages: 7

Brand: Zenisu Keisoku,Inc. Pages: 21

USB 2.0 SATA & IDE Adapter 42868v0

Brand: Lindy Pages: 2

Brand: 4B Pages: 29

Brand: Sabrent Pages: 4

Brand: Apricorn Pages: 4

Brand: Atheros Pages: 48

WiFi 2.4G RJ45 A

Brand: Epever Pages: 2

F8T031 - Bluetooth Wireless USB Printer Adapter Print Server

Brand: Belkin Pages: 93

Brand: Valcom Pages: 8

Brand: Rocom Pages: 2

Brand: Caen ELS Pages: 19

XETB1001 - 85 MBit/s Powerline Network Adapters

Brand: NETGEAR Pages: 2

Brand: WELLTECH Pages: 3

Brand: Vivo Pages: 4

U444-T6N-H4GUBC

Brand: Tripp Lite Pages: 8

Brand: Tripp Lite Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands