manualshive.com logo in svg

HP StorageWorks 2000fc, Reference Manual

Share
Download
HP StorageWorks 2000fc Reference Manual Download Page 199

Chapter 7

Troubleshooting Using SMU

199

4. In the Host-Generated I/O & Bandwidth Totals for All Virtual Disks panel, verify 

that both indicators display 0 (no activity).

Clearing Metadata From Leftover Disk Drives

A drive becomes a “leftover” when its metadata identifies the drive as being part of 
a nonexistent virtual disk, or when a controller forces the drive offline because it 
reported too many errors. SMU reports that the leftover drive is part of virtual disk 
Leftover and shows the drive as follows in enclosure view:

 

Before you can use the drive in a different virtual disk or as a spare, you must clear 
the metadata. 

To clear metadata from drives, see “Clearing Metadata From Leftover Disk Drives” 
on page 136

Isolating Faulty Disk Drives

When a drive fault occurs, basic troubleshooting actions are:

■

Identify the faulty drive

■

Review the drive error statistics

■

Review the event log

■

Replace the faulty drive

■

Reconstruct the associated virtual disk

Identifying a Faulty Disk Drive

The identification of a faulty disk drive involves confirming the drive fault and 
identifying the physical location of the drive.

To confirm a drive fault, use the basic troubleshooting steps in “Determining 
Storage System Status and Verifying Faults” on page 197. You can also view the 
Monitor > Status > Show Notification page and look for any notifications pertaining 
to a disk drive fault.

Summary of Contents for StorageWorks 2000fc











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands