manualshive.com logo in svg

HP StorageWorks 2000fc, Reference Manual

Share
Download
HP StorageWorks 2000fc Reference Manual Download Page 107

Chapter 3

Managing Storage

107

Reverting to Original Data

The snapshot service has two features for reverting data back to original data:

■

Deleting only modified data on a snapshot

■

Rolling back the data in a master volume

For snapshots that have been made accessible as read-write, you can delete just the 
modified (write) data that was written directly to a snapshot. When the modified 
data is deleted, the snapshot data reverts to the original data that was snapped. This 
feature is useful for application test, for example. You might want to test some code, 
which writes data to the snapshot. Rather than having to take another snapshot, you 
can just delete any write data and start again.

The roll back feature enables you to revert the data in a master volume to the data 
that existed when a specified snapshot was created (preserved data). You also have 
the option of rolling back to include the modified (write) data on the snapshot since 
the snapshot was taken. For example, you might want to take a snapshot, mount that 
snapshot for read/write, and then install new software on that snapshot for test 
purposes. If the software installation is successful, you can roll back the master 
volume to the contents of the modified snapshot (preserved data plus the write data).

The following figure shows the difference between rolling back the master volume 
to the data that existed when a specified snapshot was created (preserved), and 
rolling back preserved and modified data.

Summary of Contents for StorageWorks 2000fc











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands