HP StorageWorks 2000fc Reference Manual Download Page 286 | Manualshive

Page: 286 / 330

background image

286

HP StorageWorks 2000 Family Modular Smart Array reference guide • August 2008

154

Informational

New software has been loaded on the
Management Controller.

155

Informational

New loader software has been loaded
on the Management Controller.

156

Informational

The Management Controller has been
restarted from the Storage Controller.

157

Critical

A failure occurred when trying to
write to the Storage Controller flash
chip.

Replace the controller module.

160

Warning

The EMP enclosures are not
configured correctly. All enclosure
EMPs on that channel are disabled.

Check that EMP enclosures are
configured correctly and issue a
rescan.

161

Informational

One or more enclosures do not have a
valid path to an EMP. All enclosure
EMPs are disabled.

162

Warning

The host Fibre Channel World Wide
Names (node and port) previously
presented by this controller module in
this system are unknown. This event
has two possible causes:
• One or both controller modules

have been replaced or moved while
the system was powered off.

• One or both controller modules

have had their flash configuration
cleared (this is where the
previously used WWNs are stored).

The controller module recovers from
this situation by generating a WWN
based on its own serial number.

Verify the WWN information for
this controller module on all hosts
that access it.

TABLE E-1

Event Descriptions and Recommended Actions

(Continued)

Event
Code

Event Type

Description

Recommended Action

«
...
284
285
286
287
288
...
»

Summary of Contents for StorageWorks 2000fc











































































































































































































































































































































Reviews:

No comments

Related manuals for StorageWorks 2000fc

Brand: cable matters Pages: 12

Brand: Tactic Pages: 4

Freedom SW 2000

Brand: Xantrex Pages: 36

CrossPower C4L5200-ETH

Brand: C4Line Pages: 26

Brand: Gateway Pages: 68

Brand: Edimax Pages: 4

Brand: Renesas Pages: 18

Brand: Future Domain Pages: 48

Brand: BAZOO Pages: 2

Brand: l-com Pages: 34

Brand: Intermec Pages: 12

USB ADAPTER PLUS

Brand: KROHNE Pages: 16

Brand: Honeywell Pages: 2

OneWireless Adapter

Brand: Honeywell Pages: 20

Brand: Honeywell Pages: 2

Brand: Honeywell Pages: 54

Brand: Honeywell Pages: 2

Home C-Wire Adapter

Brand: Honeywell Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands