manualshive.com logo in svg

HP StorageWorks 2000fc, Reference Manual

Share
Download
HP StorageWorks 2000fc Reference Manual Download Page 257

Appendix C

Host Access to Storage

257

iSCSI

Each controller has a unique, permanent hardware address. Each controller host port 
has a unique, user-defined IP address.

The following table shows example hardware addresses and port IP addresses.

SAS

Both controllers have the same unique, permanent node WWN. Each controller host 
port has a unique port WWN that is based on the node WWN.  The WWN format is:

5

<OUI><serial-number><port-ID>

00 

■

OUI

 – The manufacturer’s unique identifier, 00C0FF.

■

serial-number

 – A serial number derived from the last six hex digits of the 

midplane serial number.

■

port-ID

 – 0 for controller A port 0; 1 for A1; 2 for B0; 3 for B1.

The following table shows example node WWNs and port WWNs. Notice that the 
node WWNs are the same and the port WWNs differ in the fourteenth digit.

Controller

Hardware Address

iSCSI Port IP Address

A

00C0FF0A8A51

0: 10.11.10.4
1: 10.10.10.5

B

00C0FF0A8A52

0: 10.11.10.2
1: 10.10.10.3

Controller

Node WWN

SAS Port WWN

A

500C0FF0A408A000

0: 500C0FF0A408A

0

00

1: 500C0FF0A408A

1

00

B

500C0FF0A408A000

0: 500C0FF0A408A

2

00

1: 500C0FF0A408A

3

00

Summary of Contents for StorageWorks 2000fc











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands