manualshive.com logo in svg

HP StorageWorks 2000fc, Reference Manual

Share
Download
HP StorageWorks 2000fc Reference Manual Download Page 287

Appendix E

Event Codes

287

163

Warning

The host FC World Wide Names 
(node and port) previously presented 
by an offline controller module in this 
system are unknown.
This event has two possible causes:
• The online controller module 

reporting the event was replaced or 
moved while the system was 
powered off.

• The online controller module had 

its flash configuration (where 
previously used WWNs are stored) 
cleared.

The online controller module 
recovers from this situation by 
generating a WWN for the other 
controller module based on its own 
serial number.

Verify the WWN information for 
the other controller module on all 
hosts that access it.

166

Warning

The RAID metadata level of the two 
controllers does not match. Usually, 
the controller at the higher firmware 
level can read metadata written by a 
controller at a lower firmware level. 
The reverse is typically not true. 
Therefore, if the controller at the 
higher firmware level failed, the 
surviving controller at the lower 
firmware level cannot read the 
metadata on drives that have failed 
over. 

Update the controller with the 
lower firmware level to match the 
firmware level on the other 
controller.

167

Warning

A diagnostic test at controller bootup 
detected an abnormal operation, 
which might require a power cycle to 
correct.

A service technician must review 
the error information returned.

TABLE E-1 

Event Descriptions and Recommended Actions 

(Continued)

Event 
Code

Event Type

Description

Recommended Action

Summary of Contents for StorageWorks 2000fc











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands