HP StorageWorks 2000fc Reference Manual Download Page 160 | Manualshive

Page: 160 / 330

background image

160

HP StorageWorks 2000 Family Modular Smart Array reference guide • August 2008

The status is OK when there are no critical or warning conditions for the element
type. If no enclosure polling data is available, a message is displayed stating this.
For information about a critical or warning condition, view the event log; see
“Viewing the Event Log” on page 171.

Controller Versions

You can view the software, hardware, and other version information for each
controller module. During normal operation, all software versions should be the
same on both controller modules. Software versions might differ briefly while you
are updating the firmware on each controller module.

To view version information:

●

Select Monitor > Status > Advanced Settings > Controller Versions.

Version information is displayed in the following four panels.

The Storage Controller Code Versions panel shows the following information:

■

Code Version – Storage Controller software version

■

Memory Controller – Memory controller software version

■

Loader Version – Storage Controller loader software version

The Management Controller Code Versions panel shows the following information:

■

Code Version – Management Controller software version

■

Loader Version – Management Controller loader software version

The Enclosure Controller Code Versions panel shows the Expander Controller
software version.

The RAID Controller Hardware Versions panel shows the following information.

■

Hardware Version – Board version number

■

CPU Type – Type of RAID controller processor:

■

Celeron 566MHz, used in a standard controller module

■

Pentium III 700MHz, used in an enhanced FC controller module

■

CPLD Version – Version of the complex programmable logic device (CPLD)

■

Host Interface Module Model – Model number of the host interface module
within a controller module

■

Host Interface Module Version – Version of the host interface module within a
controller module

■

Cache Memory Size – Cache memory size in Mbyte

«
...
158
159
160
161
162
...
»

Summary of Contents for StorageWorks 2000fc











































































































































































































































































































































Reviews:

No comments

Related manuals for StorageWorks 2000fc

Brand: Targus Pages: 10

WaveBuddy EWP-813WA1

Brand: 11Wave Technology Pages: 33

Brand: Mesa Pages: 3

Brand: Endura Pages: 2

AirStation WI-U2-433DM

Brand: Buffalo Pages: 29

N5192A UXG X-Series

Brand: Keysight Pages: 24

Brand: Keysight Technologies Pages: 24

Brand: FirmTek Pages: 30

Brand: Uplift Desk Pages: 2

Brand: Conceptronic Pages: 209

Brand: Belkin Pages: 130

Brand: Salto Pages: 2

Brand: OBDLink Pages: 12

Brand: X-Micro Pages: 22

Neomounts AWL75-450WH

Brand: NewStar Pages: 4

Brand: Linear Pages: 2

Enercell 273-332

Brand: Enercell Pages: 1

Brand: Belkin Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands