manualshive.com logo in svg

HP StorageWorks 2000fc, Reference Manual

Share
Download
HP StorageWorks 2000fc Reference Manual Download Page 36

36

HP StorageWorks 2000 Family Modular Smart Array reference guide • August 2008

Viewing Installed Licenses

To view installed licenses:

●

Select Manage > General Config > License Management > Installed Licenses.

The Licensed Features Installed panel shows whether a license certificate file is 
installed and the status of licensed features. For a licensed feature that has a 
quantity limit, the panel shows the maximum quantity available with the license and 
the baseline maximum quantity available without a license.

■

Snapshot – Shows whether snapshot services are enabled or disabled.

■

Snapshots Available – The maximum number of snapshots permitted, followed in 
parentheses by the default number permitted.

■

Snapshots In Use – The number of snapshots that exist on the system.

■

Volume Copy – Shows whether volume-copy services are enabled or disabled.

■

License File Signature – License value from the installed license certificate file.

Installing a License

To install a license certificate file that has been generated for this system:

1. Ensure that the license file has been saved to a location on your network that SMU 

can access.

2. Select Manage > General Config > License Management > Install A License.

The Load License File panel is displayed.

3. Click Browse to navigate to the location of the file and click Open.  

4. Click Load License File.

The license file is installed and a message is displayed informing you that it was 
installed successfully. The changes produced by the license file take effect 
immediately.

Summary of Contents for StorageWorks 2000fc











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands