manualshive.com logo in svg

HP StorageWorks 2000fc, Reference Manual

Share
Download
HP StorageWorks 2000fc Reference Manual Download Page 128

128

HP StorageWorks 2000 Family Modular Smart Array reference guide • August 2008

3. Select Take Snapshot.

4. Select a master volume to take snapshots of.

5. Specify a prefix to identify snapshots created by this task.

The prefix is case sensitive and can include 14 characters, but not comma, quotation 
mark ("), or backslash.

Automatically created snapshots are named 

prefix

_S

xxxx

, where 

xxxx

 

increments from 0001 to 9999 before rolling over.

6. Specify the number of snapshots with this prefix to retain.

The default and minimum value is 1. Your license determines the maximum value.

7. Specify a name for the task.

The name is case sensitive and can include 32 characters. Allowed characters 
include letters, numbers, hyphens, underscores, and spaces.

8. Click Create Task.

The Tasks panel is updated and task information is displayed in the Task Details 
panel.

Creating a Reset Snapshot Task

You can create a task to reset a snapshot, which deletes the data in the snapshot and 
resets it to the current data in the associated master volume. The snapshot's name 
and other volume characteristics are not changed.

Caution – 

Before scheduling a reset snapshot task, consider that if the snapshot is 

mounted to a host operating system, the snapshot must be unmounted before the 
reset is performed; leaving it mounted can cause data corruption.  

To create a task to reset a snapshot:

1. Select Manage > Scheduler > Manage Scheduler.

2. In the Tasks panel click Add New Task.

The Create Task panel is displayed.

3. Select Reset Snapshot.

4. Select a snapshot volume to reset.

Summary of Contents for StorageWorks 2000fc











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands