manualshive.com logo in svg

HP StorageWorks 2000fc, Reference Manual

Share
Download
HP StorageWorks 2000fc Reference Manual Download Page 224

224

HP StorageWorks 2000 Family Modular Smart Array reference guide • August 2008

8. If prompted to specify the file location and name, do so using a 

.logs

 extension.

The default file name is 

store.logs

. If you intend to capture multiple event logs, 

be sure to name the files appropriately so that they can be identified later.

Note – 

If you are using Firefox and have a download directory set, the file is 

automatically saved there.

Configuring the Debug Log

When instructed to do so by service personnel, as an Advanced Manage user you 
can configure the debug log. The debug log captures data that will help service 
personnel locate problems within the system logic.

After you configure the debug log as instructed, you will need to perform I/O to the 
system or re-create the situation that is causing the fault. This populates the debug 
log with information that service personnel can use to diagnose the system.

Note – 

The debug log only collects data after you configure it. It will not contain 

information about any problems that occurred before you configure it.

To configure the debug log:

1. Select Manage > Utilities > Debug Utilities > Debug Log Setup. 

The Debug Log Setup page is displayed.

2. Select the debug log setup you want.

■

Standard – Used for diagnosing general problems. With minimal impact on I/O 
performance, it collects a wide range of debug data.

■

I/O - Performance – Used for diagnosing I/O interface problems. Using this 
option, the debug log is dedicated to collecting I/O interface information, with 
minimal impact on I/O performance.

■

Device-Side – Used for diagnosing device-side problems. It collects device 
failure data as well as I/O interface information, with minimal impact on I/O 
performance.

■

Device Management – Collects very verbose information, including all 
Configuration API (CAPI) transactions. Because this option collects a lot of data, 
it has a substantial impact on performance and quickly fills up the debug trace.

Summary of Contents for StorageWorks 2000fc











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands