manualshive.com logo in svg

HP StorageWorks 2000fc, Reference Manual

Share
Download
HP StorageWorks 2000fc Reference Manual Download Page 310

310

HP StorageWorks 2000 Family Modular Smart Array reference guide • August 2008

I/O module (IOM)

See 

controller module

 and 

expansion module

.

IP

Internet Protocol.

IQN

ISCSI Qualified Name.

iSCSI

Internet Small Computer System Interface.

iSNS

Internet Storage Name Service.

JBOD

Just a Bunch of Disks. A drive enclosure that is directly attached to a 
host.

jumbo frame

In an iSCSI network, a frame that can contain 9000 bytes for large data 
transfers. A normal frame can contain 1500 bytes.

Kbyte (KB)

Kilobyte. Equivalent to 1000 bytes for data storage and statistics, or 
1024 bytes for memory.

LAN

See 

local area network (LAN)

.

leftover drive

A disk drive that contains metadata but is no longer part of a virtual 
disk.

local area network

(LAN)

A communications infrastructure designed to use dedicated wiring over 
a limited distance (typically a diameter of less than five kilometers) to 
connect to a large number of intercommunicating nodes. Ethernet and 
token ring are the two most popular LAN technologies. (SNIA)

logical unit number

(LUN)

The SCSI identifier of a logical unit within a target. (SNIA)

For example, a LUN identifies the mapping between a storage system 
volume and a port on a switch or HBA/NIC.

loop address

Indicates the unique ID of a node in FC loop topology. A loop address 
is sometimes referred to as a Loop ID.

loop topology

See 

Fibre Channel-Arbitrated Loop (FC-AL)

.

LUN

See 

logical unit number (LUN)

.

Management

Controller (MC)

The processor (located in a controller module) that is primarily 
responsible for human-computer interface and computer-computer 
interface functions, and interacts with the Storage Controller.

Summary of Contents for StorageWorks 2000fc











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands