HP StorageWorks 2000fc Reference Manual Download Page 237

Page: 237 / 330

Appendix A

SNMP Configuration

237

connUnitPortStatLANTable

Not supported

N/A

SNMP TRAPS

The following SNMP traps are
supported

trapMaxClients

Maximum number of trap clients

trapClientCount

Number of trap clients currently
enabled

1 if traps enabled; 0 if traps
not enabled

connUnitEventTrap

This trap is generated each time
an event occurs that passes the

connUnitEventFilter

and

the

trapRegFilter

N/A

trapRegTable

Includes the following objects per
the FA MIB2.2 Spec

trapRegIpAddress

IP address of a client registered
for traps

IP address set through
Telnet

trapRegPort

User Datagram Protocol (UDP)
port to send traps to for this host

162

trapRegFilter

Settable: Defines the trap severity
filter for this trap host. The

connUnit

will send traps to this

host that have a severity level less
than or equal to this value.

Default: warning[6]

trapRegRowState

Specifies the state of the row

• READ: rowActive[3] if

traps are enabled through
Telnet; otherwise
rowInactive[2]

• WRITE: Not supported

Table A-1

FA MIB 2.2 Objects, Descriptions, and Values

(Continued)

Object

Description

Value

Summary of Contents for StorageWorks 2000fc











































































































































































































































































































































Search results

Summary of Contents for StorageWorks 2000fc

Reviews:

Related manuals for StorageWorks 2000fc

Brands by name

Popular brands

HP StorageWorks 2000fc, Reference Manual

Search results

Summary of Contents for StorageWorks 2000fc

Reviews:

Related manuals for StorageWorks 2000fc

Brands by name

Popular brands