HP StorageWorks 2000fc Reference Manual Download Page 278

Page: 278 / 330

278

HP StorageWorks 2000 Family Modular Smart Array reference guide • August 2008

Warning

The sensors monitored a temperature
or voltage in the warning range.

• Check that the storage system’s

fans are running.

• Check that the ambient

temperature is not too warm. The
enclosure operating range is
41

F to 104

F (5

C to 40

C).

• Check for any obstructions to the

airflow.

• If none of the above explanations

apply, replace the controller FRU
that reported the error.

When the problem is fixed, event
47 is logged.

Critical

The sensors monitored a temperature
or voltage in the failure range.

• Check that the storage system’s

fans are running.

• Check that the ambient

temperature is not too warm. The
enclosure operating range is
41

F to 104

F (5

C to 40

C).

• Check for any obstructions to the

airflow.

• If none of the above explanations

apply, replace the controller FRU
that reported the error.

When the problem is fixed, event
47 is logged.

Informational

A vdisk spare has been added.

Informational

A vdisk has been deleted.

Warning

The controller contains dirty cache
data for the specified volume but the
corresponding disk drives are not
online.

• Determine the reason that the

drives are not online.

• If an enclosure is down,

determine corrective action.

• If the virtual disk is no longer

needed, you can clear the orphan
data; this will result in lost data.

TABLE E-1

Event Descriptions and Recommended Actions

(Continued)

Event
Code

Event Type

Description

Recommended Action

Summary of Contents for StorageWorks 2000fc











































































































































































































































































































































Search results

Summary of Contents for StorageWorks 2000fc

Reviews:

Brands by name

Popular brands

HP StorageWorks 2000fc, Reference Manual

Search results

Summary of Contents for StorageWorks 2000fc

Reviews:

Brands by name

Popular brands