manualshive.com logo in svg

HP StorageWorks 2000fc, Reference Manual

Share
Download
HP StorageWorks 2000fc Reference Manual Download Page 314

314

HP StorageWorks 2000 Family Modular Smart Array reference guide • August 2008

SCSI Enclosure

Services (SES)

An ANSI X3T10 standard for management of environmental factors 
such as temperature, power, voltage, etc. (SNIA) 

In MSA2000 Family storage systems, SES data is managed by the 
Expander Controller and EMP.

secret

For use with CHAP, a password that is shared between an initiator and 
a target to enable authentication.

SFP

Small form-factor pluggable connector, used in FC controller module 
host ports. An SFP is a FRU.

SID

Secondary controller identifier number.

SMART

Self-Monitoring Analysis and Reporting Technology. The industry-
standard reliability prediction indicator for both the IDE/ATA and SCSI 
hard disk drives. Hard disk drives with SMART offer early warning of 
some hard disk failures so critical data can be protected.

SMI-S

Storage Management Interface Specification.

SMTP

Simple Mail Transfer Protocol. A protocol for sending email messages 
between servers and from mail clients to mail servers. The messages 
can then be retrieved with an email client using either POP or IMAP. 

SMU

Storage Management Utility. The web browser interface that system 
administrators can use to configure, monitor, and manage MSA2000 
Family storage systems. SMU is accessible from any management host 
that can access a system through an out-of-band Ethernet connection.

snap pool

A volume that is configured to store snapshot data.

snapshot

A fully usable copy of a defined collection of data that contains an 
image of the data as it appeared at the point in time at which the copy 
was initiated. (SNIA)

SNIA

Storage Networking Industry Association.

SNMP

Simple Network Management Protocol. An IETF protocol for 
monitoring and managing systems and devices in a network. The data 
being monitored and managed is defined by a MIB. The functions 
supported by the protocol are the request and retrieval of data, the 
setting or writing of data, and traps that signal the occurrence of events. 
(SNIA)

spare

See 

dynamic spare

, 

global spare

, 

vdisk spare

.

Summary of Contents for StorageWorks 2000fc











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands