HP StorageWorks 2000fc Reference Manual Download Page 201 | Manualshive

Page: 201 / 330

background image

Chapter 7

Troubleshooting Using SMU

201

4. Note any error counts displayed for these statistics.

Field

Description

SMART Event Count

The number of SMART (Self-Monitoring Analysis and
Reporting Technology) events that the drive recorded.
These events are often used by the vendor to determine
the root cause of a drive failure. Some SMART events
may indicate imminent electromechanical failure.

I/O Timeout Count

The number of times the drive accepted an I/O request
but did not complete it in the required amount of time.
Excessive timeouts can indicate potential device failure
(media retries or soft, recoverable errors)

No Response Count

The number of times the drive failed to respond to an I/O
request. A high value can indicate that the drive is too
busy to respond to further requests.

Spin-up Retries

The number of times the drive failed to start on power-up
or on a software request. Excessive spin-up retries can
indicate that a drive is close to failing.

Media Errors

The number of times the drive had to retry an I/O
operation because the media did not successfully
record/retrieve the data correctly.

Non Media Errors

The number of soft, recoverable errors that are not
associated with drive media.

Bad Block Reassignments

The number of block reassignments that have taken place
since the drive was shipped from the vendor. A large
number of reallocations in a short period of time could
indicate a serious condition.

Bad Block List Size

The number of blocks that have been deemed defective
either from the vendor or over time due to reallocation.

«
...
199
200
201
202
203
...
»

Summary of Contents for StorageWorks 2000fc











































































































































































































































































































































Reviews:

No comments

Related manuals for StorageWorks 2000fc

Brand: Oehlbach Pages: 84

TravelCharge Companion HT 3.4

Brand: Wagan Pages: 16

Brand: Modecom Pages: 24

Brand: Edimax Pages: 30

Brand: Proyecson Pages: 148

Brand: TP-Link Pages: 33

Brand: Moes Pages: 14

Brand: Alvarion Pages: 2

Brand: Vantec Pages: 13

Wake-On LAN Adapter

Brand: Edimax Pages: 8

Brand: Cellink Pages: 31

Brand: StarTech.com Pages: 10

10/100/1000 Base-TX Ethernet PCI-X Adapter

Brand: IBM Pages: 32

Brand: Crown Pages: 12

RangeMax WNDA3100

Brand: NETGEAR Pages: 20

Brand: Askey Pages: 5

Brand: NETGEAR Pages: 2

Brand: NETGEAR Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands