HP StorageWorks 2000fc Reference Manual Download Page 209

Page: 209 / 330

Chapter 7

Troubleshooting Using SMU

209

Isolating External Data Path Faults on an iSCSI
Storage System

To troubleshoot external data path faults, perform the following steps:

1. Select Monitor > Status > Advanced Settings > Host Port Status.

This page provides a graphical representation of controller host port status and port
details.

2. Review the graphical representation of host port status.

■

Green – Host link is up (connected)

■

White – Host link is down (not connected)

An indication of link down can be caused by one or more of the following
conditions:

■

A faulty HBA or NIC in the host

■

A faulty Ethernet cable

■

A faulty port in the host interface module

■

A disconnected cable

3. To target the cause of the link failure, view the host port details by clicking on a

port in the graphical view and then reviewing the details listed below it.

The data displayed includes:

■

iSCSI Port Status Details – Selected controller and port number

■

Link Status – Link is up or down

■

Qualified Name – iSCSI qualified name (IQN)

■

Link Speed – Actual link speed, in Gbit/sec

■

IP Version – IP addressing version; 4 for IPv4

■

IP Address – Port IP address

■

IP Mask – Port IP subnet mask

■

IP Gateway – Port gateway IP address

■

Service Port – iSCSI port number

■

Hardware Address – Port MAC address

Summary of Contents for StorageWorks 2000fc











































































































































































































































































































































Search results

Summary of Contents for StorageWorks 2000fc

Reviews:

Brands by name

Popular brands

HP StorageWorks 2000fc, Reference Manual

Search results

Summary of Contents for StorageWorks 2000fc

Reviews:

Brands by name

Popular brands