manualshive.com logo in svg

HP StorageWorks 2000fc, Reference Manual

Share
Download
HP StorageWorks 2000fc Reference Manual Download Page 155

Chapter 5

Monitoring System Status

155

Details in the lower part of the panel vary depending on the selected port’s status.

■

Topology – Port connection type.

■

Speed – Actual link speed in Gbit per second per PHY lane.

■

Number of Active Lanes - The number of active PHY lanes and the number of 
lanes in the port.

■

Port WWN – Port World Wide Name.

■

Health – Port status:

■

Healthy – All PHY lanes are active in the port.

■

Degraded – At least one PHY lane is inactive in the port.

■

SAS Chip Revision – Hardware revision level of the SAS expander processor in 
the controller.

■

SAS Libraries Revision – Firmware revision level of the SAS libraries.

Disk Drive List

To view information about all disk drives in the storage system:

●

Select Monitor > Status > Advanced Settings > Disk Drive List.

This page shows the total number of drives that:

■

Are installed

■

Are available (have Available status)

■

Contain leftover metadata from a previous virtual disk

■

Are down (failed)

It also shows the following information about each drive:

■

Status – Up if operational or Down if failed.

■

Size – Drive size in Gbyte.

■

Speed – Data transfer rate in Gbit per second.

■

Manufacturer – Drive manufacturer.

■

Model – Drive model number.

■

Revision – Drive firmware revision.

■

Node WWN – Drive node World Wide Name.

■

Serial Number – Drive serial number.

■

Encl.Slot – Enclosure number and slot number containing the drive.

Summary of Contents for StorageWorks 2000fc











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands