HP StorageWorks 2000fc Reference Manual Download Page 275 | Manualshive

Page: 275 / 330

background image

275

A P P E N D I X

E

Event Codes

Information in this appendix is for reference by storage administrators and technical
support personnel to aid troubleshooting.

Event messages appear in the event log, which you can view using SMU or the CLI,
and in debug logs. You may also receive notifications, depending on your SMU
event notification settings.

The following table describes the events that can occur during operation. Events are
listed in order by numeric event code. Recommended actions available at this time
are also listed.

TABLE E-1

Event Descriptions and Recommended Actions

Event
Code

Event Type

Description

Recommended Action

1

Warning

A disk drive in the specified vdisk
failed. The vdisk is online but not
fault tolerant. If a spare is present the
controller automatically uses the
spare to reconstruct the vdisk.

• See “Disk Drive Errors and

Recommended Actions” on
page 300.

• If dynamic spares is enabled,

replace the failed drive. The
system automatically
reconstructs the vdisk.

• If dynamic spares is disabled and

no spare is available, replace the
failed drive and add it as a vdisk
spare to the critical vdisk.

3

Critical

The specified vdisk is now offline. If
a spare is present the controller
automatically uses the spare to
reconstruct the vdisk.

If no spare is available, replace the
failed drive and add it as a vdisk
spare to the critical vdisk.

4

Informational

A drive had an uncorrectable error
and the controller reassigned the
block.

«
...
273
274
275
276
277
...
»

Summary of Contents for StorageWorks 2000fc











































































































































































































































































































































Reviews:

No comments

Related manuals for StorageWorks 2000fc

Brand: 3idee Pages: 5

Brand: Uconnect Pages: 8

Brand: P.I. Engineering Pages: 4

Brand: ZyXEL Communications Pages: 4

Netkey 73-TMWBG-001

Brand: TwinMOS Pages: 25

DMXpro LP510-001

Brand: Synapse Pages: 21

Brand: 3idee Pages: 6

Brand: CAB Pages: 10

Brand: Eskridge Pages: 4

Brand: HDTV Supply Pages: 4

Brand: Qlogic Pages: 82

Brand: Sanwa Pages: 2

Brand: Belkin Pages: 2

Brand: Belkin Pages: 32

Brand: Belkin Pages: 42

Brand: Belkin Pages: 52

Wireless G Router

Brand: Belkin Pages: 111

ShareTime ST100-001

Brand: Altinex Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands