HP StorageWorks 2000fc Reference Manual Download Page 115 | Manualshive

Page: 115 / 330

background image

Chapter 3

Managing Storage

115

Resetting a Snapshot

You can reset a snapshot to replace its content with the current data state of the
associated master volume. The selected snapshot is replaced with a current snapshot
having the same characteristics, such as name and LUN. The snapshot data is stored
in the snap pool associated with the master volume. Before being reset, a snapshot
must be unmounted from hosts.

Caution –

Before resetting a snapshot you must unmount it from data hosts to

avoid data corruption.

To reset a snapshot:

1. Unmount the snapshot from hosts.

2. Select Manage > Volume Management > Snapshot Services > Reset Snapshot.

For each virtual disk, the virtual disk panel shows a status icon; the name, RAID
level, size, number of disk drives, and number of volumes; and utility status, if any.

3. Select a virtual disk.

The selected virtual disk’s volume names, sizes, and types are displayed, and the
amount of free space.

4. Select the snapshot to reset.

5. Click Reset Snapshot.

When processing is complete, a message indicates whether the operation succeeded.

Deleting Modified Data

If a snapshot has been made accessible as read-write, you have the option of
deleting only the modified (write) data that has been written to it. (See “Managing
Volume Mappings” on page 99 for information about setting access privileges.) The
amount of data that has been written to a snapshot is shown in the Unique Data field
on the Snapshot Overview page. (See the information provided for snapshots in
“Viewing Information About Snap Pools, Master Volumes, and Snapshots” on
page 118.) You must unmount the snapshot from hosts before deleting modified
data.

«
...
113
114
115
116
117
...
»

Summary of Contents for StorageWorks 2000fc











































































































































































































































































































































Reviews:

No comments

Related manuals for StorageWorks 2000fc

Brand: ID Systems Pages: 12

RANGEBOOSTER N 650

Brand: D-Link Pages: 24

Brand: j5 create Pages: 7

Brand: Sennheiser Pages: 59

Brand: Emulex Pages: 2

Brand: AGFEO Pages: 12

Brand: Vantec Pages: 5

Brand: Pace Pages: 15

Brand: VSmart Pages: 9

harman/kardon CITATION ADAPT

Brand: Harman Pages: 31

Brand: MillSO Pages: 2

Brand: Flexport Pages: 17

Brand: Airlink101 Pages: 47

Brand: Intermec Pages: 102

omni.net LCD series

Brand: ZyXEL Communications Pages: 53

Brand: 3idee Pages: 8

Brand: Targus Pages: 8

Brand: SP Controls Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands