manualshive.com logo in svg

HP StorageWorks 2000fc, Reference Manual

Share
Download
HP StorageWorks 2000fc Reference Manual Download Page 68

68

HP StorageWorks 2000 Family Modular Smart Array reference guide • August 2008

7. Select the drives to use in the virtual disk.

Only available drives are selectable. Available drives are neither in a virtual disk nor 
assigned as a spare.

The minimum and maximum number of drives that you can select when creating a 
virtual disk are shown in Table 3-1.

In a multi-enclosure system, for certain RAID levels you can select drives in a way 
that provides some protection against enclosure failure:

■

RAID 1, 3, 5, or 6 – Select each drive from a different enclosure.

■

RAID 10 – Select the first half of the drives from one enclosure and the second 
half from another enclosure. The first set is assigned to one mirror group and the 
second to other mirror group, which limits the effect of an enclosure failure to 
one mirror.

■

RAID 50 – Drives that you select consecutively are assigned to different sub-
vdisks in the virtual disk. Therefore, you can force the drives in each sub-vdisk to 
be selected from different enclosures, improving the protection of each sub-vdisk 
from an enclosure failure.

8. (Optional) Calculate whether the formatted virtual disk will have the capacity you 

want:

a. Click Calculate Virtual Disk Size.

The results of the calculation are displayed.

b. Click OK.

If the capacity is insufficient for your application, change your drive selections 
and repeat this step.

9. (Optional, but recommended) If the add dedicated spare drives option is displayed 

you can reserve spares for use only by this virtual disk:

a. Set the add dedicated spares option to Yes.

The default is No.

b. Click Continue.

The Select Spare Drives page is displayed.

c. Select the check box of each drive to use as a spare in the virtual disk.

A drive has a check box if the drive is available and meets the minimum size and 
type requirements of the virtual disk.

You can add four spares to a virtual disk.

Summary of Contents for StorageWorks 2000fc











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands