hopf 8029HEPTA-V2/GPS Technical Manual Download Page 8

Page: 8 / 130

ABLE OF

ONTENTS

8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00

8 / 130

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

11.3

Cleaning the Display and Front Panel.................................................................... 112

Technical Data .......................................................................................................... 113

12.1

General

– 8029HEPTA/GPS ................................................................................. 113

12.2

Module 8029HEPTA .............................................................................................. 115

12.3

Module 8024GPS .................................................................................................. 116

Factory Defaults of Time Server 8029HEPTA/GPS ................................................. 117

13.1

Factory Default Values of Module 8029HEPTA (Device) ....................................... 117

13.1.1

Network ............................................................................................................................ 117

13.1.2

NTP .................................................................................................................................. 118

13.1.3

ALARM ............................................................................................................................. 119

13.1.4

DEVICE ............................................................................................................................ 119

13.2

Factory Default Values of Module 8024GPS (Sync Source) .................................. 120

Glossary and Abbreviations .................................................................................... 121

14.1

NTP-specific Terminology...................................................................................... 121

14.2

Tally Codes (NTP-specific) .................................................................................... 121

14.2.1

Time-Specific Expressions ............................................................................................... 122

14.3

Abbreviations ......................................................................................................... 123

14.4

Definitions ............................................................................................................. 124

14.4.1

DHCP (Dynamic Host Configuration Protocol) ................................................................ 124

14.4.2

NTP (Network Time Protocol) .......................................................................................... 124

14.4.3

SNMP (Simple Network Management Protocol) .............................................................. 125

14.4.4

TCP/IP (Transmission Control Protocol / Internet Protocol) ............................................ 125

14.5

Accuracy & NTP Basic Principles .......................................................................... 125

List of RFCs ............................................................................................................... 127

List of Open Source Packages Used ....................................................................... 128

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands

hopf 8029HEPTA-V2/GPS, Technical Manual

Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands