hopf 8029HEPTA-V2/GPS Technical Manual Download Page 103 | Manualshive

Page: 103 / 130

background image

HTTP/HTTPS

W

EB

GUI

–

W

EB

B

ROWSER

C

ONFIGURATION

I

NTERFACE

8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00

103 / 130

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

8.3.6.10 Module Reset

This function triggers a hardware reset of (just) the Sync Source (here Module 8024GPS).

This function has no effect on the failsafe stored data.

8.3.6.11 Factory Default

After setting the Sync Source to factory default values the GPS receiver
needs up to 13 minutes of satellite reception in order to generate the correct
information on the leap second from the GPS data. Only then the Sync
Source (here Module 8024GPS) can be synchronized.

During this time (however only when the GPS receiver really receives
satellites) the following message is displayed in the tab

Module Errors

:

GPS Receiver in raw data mode - no synchronisation

If the changeover times for summer/winter time and the difference time are not
initial set after a factory default of the Sync Source (here Module 8024GPS)
the following message is displayed in the tab

Module Errors

:

Missing data for Time Zone Offset

and/or

Missing or incomplete data for daylight saving time (DST)

«
...
101
102
103
104
105
...
»

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Reviews:

No comments

Related manuals for 8029HEPTA-V2/GPS

Brand: Takeuchi Pages: 28

Brand: RBR Pages: 62

Brand: lancer Pages: 12

Brand: Stratasys Pages: 23

Brand: Aqua Medic Pages: 24

Brand: Suki Pages: 6

Brand: Onewheel+ Pages: 26

Brand: Warn Pages: 14

Koi Pro UVC 40 Watt

Brand: SuperFish Pages: 16

Brand: ComAp Pages: 105

Brand: VIGO Pages: 25

Brand: FBI Pages: 9

Brand: Daka Corporation Pages: 17

Brand: EAGO Pages: 16

Brand: Sagem Pages: 284

Brand: JBJ Pages: 24

Brand: easy2read Pages: 12

METPOINT BDL compact

Brand: Beko Pages: 118

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands