hopf 8029HEPTA-V2/GPS Technical Manual Download Page 68

Page: 68 / 130

HTTP/HTTPS

GUI

–

ROWSER

ONFIGURATION

NTERFACE

8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00

68 / 130

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

8.3.3.4 Server Configuration

The basic settings for NTP base functionality are displayed selecting the “Server
Configuration” link.

The

hopf

– refclock ntp driver

is already configured as standard (127.127.38.0 in the “Peers

Summary”) and is not explicitly displayed here.

8.3.3.4.1 Synchronization Source (General / Synchronization source)

"Synchronization source"

either GPS or DCF77, depending on the appropriate Sync

Source, has to be selected. This is required in order to align the NTP algorithm for the
calculation of the accuracy with the synchronization source.

Based on the selection of GPS, even though GPS is not the source of the
Sync Source (different product option) the value

HIGH

for

Accuracy

may

never be reached.

8.3.3.4.2 NTP Syslog Messages (General / Log NTP Messages to Syslog)

This option enables or disables Syslog messages which are generated from the NTP service.

This value has no effect if Syslog is not configured in the ALARM tab (see

Chapter 8.3.4.1

Syslog Configuration

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands

hopf 8029HEPTA-V2/GPS, Technical Manual

Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands