hopf 8029HEPTA-V2/GPS Technical Manual Download Page 61

Page: 61 / 130

HTTP/HTTPS

GUI

–

ROWSER

ONFIGURATION

NTERFACE

8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00

61 / 130

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

8.3.2.5 Management (Management-Protocols

– HTTP, SNMP, SNMP-Traps, etc.)

Protocols that are not required should be disabled for security reasons. A correctly configured
module is always accessible via the web interface.

Changes to the availability of a protocol (enable/disable) take effect immediately.

For SNMP functionality an activation key is necessary.

If by mistake all protocol channels become "disabled", the SSH channel is
automatically "enabled" after the attempt to save.

After a Factory Default the HTTP and SSH channels are "enabled".

These service settings are valid globally! "Disabled" Services are not
externally accessible and are not made externally available by the module!

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands

hopf 8029HEPTA-V2/GPS, Technical Manual

Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands