hopf 8029HEPTA-V2/GPS Technical Manual Download Page 53 | Manualshive

Page: 53 / 130

background image

HTTP/HTTPS

W

EB

GUI

–

W

EB

B

ROWSER

C

ONFIGURATION

I

NTERFACE

8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00

53 / 130

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

8.3.2.1.1 Use Manual DNS Entries

With this setting you can select whether the manually entered DNS servers (DNS servers 1 to
3) should be used.

If "enabled" is selected here, the entries in DNS Server 1 to 3 are used.

If "disabled" is selected, the entries in DNS Server 1 to 3 are ignored.

If a DHCP server is used to distribute the network configuration and if this
also distributes the DNS servers used in the network, then

Use Manual

DNS Entries

should be set to disabled.

8.3.2.1.2 DNS Server 1 to 3

The IP address (IPv4 or IPv6) of the DNS server should be entered if you wish to use the Fully-
Qualified Host Name (hostname.domainname) or work with reverse lookup

Contact your network administrator for details of the DNS server if not known.

If no DNS server is available (special case), enter 0.0.0.0 in the input field or leave the field
blank.

8.3.2.1.3 Use Manual Gateway Entries

With this setting, you can select whether the manually entered gateways (Default Gateway
IPv4 and Default Gateway IPv6) should be used.

If "enabled" is selected here, the entries in Default Gateway IPv4 and Default Gateway IPv6
are used.

If "disabled" is selected, the entries in Default Gateway IPv4 and Default Gateway IPv6 are
ignored.

If a DHCP server is used to distribute the network configuration and if this
also distributes the address of the default gateway used in the network,
then Use Manual Gateway Entries should be set to disabled.

8.3.2.1.4 Default Gateway IPv4

If the IPv4 default gateway is not known, it must be requested by the network administrator. If
no standard gateway is available (special case), enter 0.0.0.0 in the input field or leave the
field blank.

8.3.2.1.5 Default Gateway IPv6

If the Ipv6 default gateway is not known, it must be requested by the network administrator. If
no standard gateway is available (special case), enter :: in the input field or leave the field
blank.

«
...
51
52
53
54
55
...
»

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Reviews:

No comments

Related manuals for 8029HEPTA-V2/GPS

Brand: Gerni Pages: 60

Brand: Fass Pages: 28

Brand: SAelen TS Pages: 44

Brand: Fujitsu Pages: 111

Brand: Fujitsu Pages: 543

Brand: IAG Pages: 49

Brand: Aqua Medic Pages: 25

Brand: PROEL Pages: 76

Brand: Xvive Audio Pages: 16

Brand: DITEC Pages: 30

Brand: Valve Pages: 76

Tornado BR 4735 ESC

Brand: Kärcher Pages: 18

Brand: Finest Pages: 15

GasAlertMicroClip Series

Brand: BW Technologies Pages: 57

Brand: Majestic Pages: 15

Brand: Majestic Pages: 17

Brand: Racelogic Pages: 5

VITRO 750 Black

Brand: Ducasa Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands