manualshive.com logo in svg

hopf 8029HEPTA-V2/GPS, Technical Manual, Page: 28 / 130

Share
Download
hopf 8029HEPTA-V2/GPS Technical Manual Download Page 28

 

I

NSTALLATION

 

 

 

 8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00 

28 / 130 

hopf 

Elektronik GmbH   

Nottebohmstr. 41 

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected] 

5.2  

Connection GPS Antenna System 

The coaxial line of the GPS antenna system is placed on the BNC female connector with the 

"GPS  Antenna" 

inscription  on  the  rear  side  of  the  Time  Server  8029HEPTA/GPS.  More 

detailed  descriptions  referring  to  the  installation  of  the  antenna  system,  for  example,  cable 
lengths and c

able types, are described in the document “Antenna System GPS”. 

 

 

GPS Antenna 

BNC connector 

GPS 

Antenna input 

 

 

 

There is an antenna input monitoring for "open" and "short-circuit" on the 
system side. 

 

5.3  

Connection LAN Interface ETH0 

 

 

10/100-LED (Green) 

Description 

Off 

10 MBit Ethernet detected 

On 

100 MBit Ethernet detected 

 

lnk/act-LED (Yellow) 

Description 

Off 

No LAN connection to a network 

On 

LAN connection available 

Flashes 

Network activity at ETH0 (transmission 
/ reception) 

 

Pin No. 

Assignment 

1 

Tx+ 

2 

Tx

– 

3 

Rx+ 

4 

Not in use 

5 

Not in use 

6 

Rx

– 

7 

Not in use 

8 

Not in use 

 

 

 

 

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Reviews:

No comments