hopf 8029HEPTA-V2/GPS Technical Manual Download Page 64

Page: 64 / 130

HTTP/HTTPS

GUI

–

ROWSER

ONFIGURATION

NTERFACE

8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00

64 / 130

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

8.3.2.6 Time (Time Protocols

– NTP, DAYTIME etc.)

Activation and configuration of different synchronization protocols

All protocols can be enabled at the same time.

8.3.2.6.1 Synchronization Protocols (Time Protocols

– NTP, SNTP etc.)

Needed time protocols can be enabled here.

•

NTP (incl. SNTP)

•

DAYTIME

•

TIME

•

SINEC H1 time datagram (Activation Key necessary)

8.3.2.6.2 SINEC H1 Time Datagram (Activation Key necessary)

Configuration of the SINEC H1 time datagram

Broadcast transmission intervals of the SINEC H1 time datagram (Send Interval)

•

every second

•

every 10 second

•

every 60 second

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands

hopf 8029HEPTA-V2/GPS, Technical Manual

Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands