manualshive.com logo in svg

hopf 8029HEPTA-V2/GPS, Technical Manual, Page: 16 / 130

Share
Download
hopf 8029HEPTA-V2/GPS Technical Manual Download Page 16

 

S

YSTEM 

S

TRUCTURE

 

 

 

 8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00 

16 / 130 

hopf 

Elektronik GmbH   

Nottebohmstr. 41 

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected] 

2.2.6   LAN Interface ETH0 

 

10/100-LED (Green) 

Description 

Off 

10 MBit Ethernet detected 

On 

100 MBit Ethernet detected 

 

lnk/act-LED (Yellow) 

Description 

Off 

No LAN connection to a network 

On 

LAN connection available 

Flashes 

Network activity at ETH0 (transmission 
/ reception) 

 

Pin No. 

Assignment 

1 

Tx+ 

2 

Tx

– 

3 

Rx+ 

4 

Not in use 

5 

Not in use 

6 

Rx

– 

7 

Not in use 

8 

Not in use 

 

 

2.2.6.1  MAC-Address for ETH0 

Each LAN interface is clearly identifiable on the Ethernet via a unique MAC Address (hardware 
address).  

The MAC address given for the LAN interface ETH0 can be read in WebGUI of the appropriate 
board or be evaluated via the 

hmc 

Network Configuration Assistant.

  The MAC address 

is uniquely assigned for each LAN interface by the company 

hopf 

Elektronik GmbH. 

 

The factory set MAC address for the Time Server 8029HEPTA/GPS can 
also be read out via the LCD-Display

.

 

 

 

hopf 

Elektronik GmbH MAC addresses begin with 

00:03:C7

:xx:xx:xx. 

 

2.2.7   Sync Status Optical Coupler 

 

Sync Status Optical Coupler 

3-pole pluggable Connector 

Pin 

Signal 

1 

Collector 

2 

n.c. 

3 

Emitter 

 

 

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Reviews:

No comments