hopf 8029HEPTA-V2/GPS Technical Manual Download Page 50

Page: 50 / 130

HTTP/HTTPS

GUI

–

ROWSER

ONFIGURATION

NTERFACE

8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00

50 / 130

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

8.3

Description of the Tabs

The WebGUI is divided into the following tabs:

•

General

•

Network

•

NTP

•

Alarm

•

Device

•

GPS Sync Source

8.3.1 GENERAL Tab

This is the first tab displayed when using the web interface.

NTP Time Status

This area shows basic information about the current time and date of the Time Server
8029HEPTA/GPS. The time

always

corresponds to UTC. The reason for this is that NTP

always works with UTC and not with local time.

Stratum displays the actual NTP stratum value of the Time Server 8029HEPTA/GPS with the
value range from 1-16.

The

ACCURACY

field (accuracy of NTP) can contain the values LOW - MEDIUM - HIGH. The

meaning of these values is explained in

Chapter 14.5

Accuracy & NTP Basic Principles

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands

hopf 8029HEPTA-V2/GPS, Technical Manual

Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands