hopf 8029HEPTA-V2/GPS Technical Manual Download Page 97

Page: 97 / 130

HTTP/HTTPS

GUI

–

ROWSER

ONFIGURATION

NTERFACE

8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00

97 / 130

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

•

Year

Input of the current UTC year (2000-2099)

•

Month

Input of the current UTC month (01-12)

•

Day

Input of the current UTC day (01-31)

•

Hour

Input of the current UTC hour (00-23)

•

Minute

Input of the current UTC minute (00-59)

•

Second

Input of the current UTC second (00-59)

The input must be complete and according to the stated format.

8.3.6.3 Time Zone Offset

Setting of the difference time (Time Zone Offset) from UTC to the local standard time (winter
time) in the Sync Source (here Module 8024GPS)

The difference time to be entered

always

relates to

the local standard

time (winter time)

even though the commissioning or rather the input of the

difference time takes place during daylight saving time.

•

Offset Hours

Time Zone Offset input of the full hour (0-13)

•

Offset Minutes

Time Zone Offset input of minutes (0-59)

Example

Time Offset for Germany



East, 1 hour and 0 minutes (+ 01:00)

Time Offset for Peru



West, 5 hours and 0 minutes (- 05:00)

Direction relating to Prime Meridian

– Direction of the Difference Time

Entering the direction the local time deviates from world time

'East'

corresponds to east,

'West'

corresponds to west of the Prime-Meridian (Greenwich)

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands

hopf 8029HEPTA-V2/GPS, Technical Manual

Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands