hopf 8029HEPTA-V2/GPS Technical Manual Download Page 105

Page: 105 / 130

HTTP/HTTPS

GUI

–

ROWSER

ONFIGURATION

NTERFACE

8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00

105 / 130

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

8.3.6.13 Module Errors

This tab displays the current failure status of the Sync Source (here Module 8024GPS):

If a collected error message is displayed in the GENERAL tab, there is at
least one error (Sync Source Error).

This page is updated automatically every 5 seconds.

Overview Software Errors

•

General Module error (PCID)

If this error occurs even after a Power down, the device is damaged.

•

GPS receiver initialization active

This condition might last for max. 1 minute after particular actions.

•

Missing data for Time Zone Offset

Difference time (Time Zone Offset) must be an initial entry by the user.

Otherwise there is no synchronization of the Sync Source (here Module 8024GPS).

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands

hopf 8029HEPTA-V2/GPS, Technical Manual

Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands