hopf 8029HEPTA-V2/GPS Technical Manual Download Page 89

Page: 89 / 130

HTTP/HTTPS

GUI

–

ROWSER

ONFIGURATION

NTERFACE

8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00

89 / 130

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

8.3.5.5.1 Select Image Update

ATTENTION

Important note for the identification of the required image update!

In order to select the correct image update, the

digit marked red

of the

serial number must be checked!

Required ZIP archive for the Image Update:

Red marked digit

= 1

Red marked digit

= 4

hopf8029HEPTA-V2-

SERI

_GPS_SET_v07xx.zip

hopf8029HEPTA-V2-

NAND

_GPS_SET_v07xx.zip

Content of the ZIP archive

•

8024A_128_v01xx.mot

•

8029HEPTA-V2_128_v05xx.mot

•

readme_8029HEPTA-V2-SERI_GPS.txt

•

release-notes_8029HEPTA-V2-SERI_GPS.html

•

upgrade_8029-

SERI

_gen_rel_v07xx.img

Content of the ZIP archive

•

8024A_128_v01xx.mot

•

8029HEPTA-V2_128_v05xx.mot

•

readme_8029HEPTA-V2-NAND_GPS.txt

•

release-notes_8029HEPTA-V2-NAND_GPS.html

•

upgrade_8029-

NAND

_gen_rel_v07xx.img

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands

hopf 8029HEPTA-V2/GPS, Technical Manual

Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands