hopf 8029HEPTA-V2/GPS Technical Manual Download Page 117

Page: 117 / 130

ACTORY

EFAULTS OF

IME

ERVER

8029HEPTA/GPS

8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00

117 / 130

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

Factory Defaults of Time Server 8029HEPTA/GPS

This chapter lists the factory default values of the individual components integrated in the Time
Server 8029HEPTA/GPS.

13.1 Factory Default Values of Module 8029HEPTA (Device)

The default delivery status of the Time Server 8029HEPTA/GPS meets the factory default
values when using GPS synchronization sources. In case of DCF77 synchronization (different
product variant) the function

"NTP / General / Sync Source"

is factory-set to

"DCF77"

delivery.

Using the board in DCF77 systems (different product variant) the setting
for

"NTP / General / Sync Source"

needs to be re-configured to

"DCF77"

after a factory default.

NTP Server Configuration

Setting

WebGUI

Sync Source

GPS

13.1.1 Network

Host/Name Service

Setting

WebGUI

Hostname

hopf8029HEPTA

Use Manual DNS Entries

Enabled

DNS Server 1 IPv4/IPv6 Address

Blank

---

DNS Server 2 IPv4/IPv6 Address

Blank

---

DNS Server 3 IPv4/IPv6 Address

Blank

---

Use Manual Gateway Entries

Enabled

Default Gateway IPv4 Address

Blank

---

Default Gateway IPv6 Address

Blank

---

Network Interface ETH0

Setting

WebGUI

Use Custom Hardware Address (MAC)

Disabled

Custom Hardware Address (MAC)

Blank

---

DHCP

Disabled

IPv4

192.168.0.1

IPv4-Netmask

255.255.255.0

Operation mode

Auto negotiate

VLAN Interfaces

Disabled

IPv6 Settings

Disabled

Routing

Setting

WebGUI

Use Route File

Disabled

User Defined Routes

Blank

---

Management

Setting

WebGUI

HTTP

Enabled

HTTPS

Disabled

SSH

Enabled

TELNET

Disabled

SNMP

Disabled

System Location

Blank

---

System Contact

Blank

---

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands

hopf 8029HEPTA-V2/GPS, Technical Manual

Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands