manualshive.com logo in svg

hopf 8029HEPTA-V2/GPS, Technical Manual, Page: 33 / 130

Share
Download
hopf 8029HEPTA-V2/GPS Technical Manual Download Page 33

 

C

OMMISSIONING

 

 

 

 8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00 

33 / 130 

hopf 

Elektronik GmbH   

Nottebohmstr. 41 

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected] 

 

The  base  LAN  parameters  can  be  set  via  the 

hmc

  integrated 

Network  Configuration 

Assistant

. 

 

 

 

After a successful start of the 

hmc 

Network Configuration Assistant

 and completed search 

of the 

hopf 

LAN devices, the configuration of the base LAN parameters can be done.  

 

The Time Server 8029HEPTA/GPS is stated as 

8029HEPTA in the

 

Device List. 

The determination of different Time Server 8029HEPTA/GPS (or other products variants) is 
made via 

Hardware Address

 (MAC Address). 

 

The factory set MAC address for the Time Server 8029HEPTA/GPS can 
also be read out via the LCD-Display

.

 

 

 

 

 

 

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Reviews:

No comments