manualshive.com logo in svg

hopf 8029HEPTA-V2/GPS, Technical Manual, Page: 58 / 130

Share
Download
hopf 8029HEPTA-V2/GPS Technical Manual Download Page 58

 

HTTP/HTTPS

 

W

EB

GUI

 

–

 

W

EB 

B

ROWSER 

C

ONFIGURATION 

I

NTERFACE

 

 

 

 8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00 

58 / 130 

hopf 

Elektronik GmbH   

Nottebohmstr. 41 

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected] 

 

WebGUI with activated VLAN 

To be able to configure VLANs the activation status must be set to "enabled" first. Afterwards 
up to 32 different VLANs per network interface can be configured by clicking the button "Add".   

An explicit VLAN ID must be configured for each VLAN interface.  

The boxes "Label" and "Remark" can be filled out with a designation or a comment to easily 
keep the configured VLANs apart.  

Determination  of  the  IPv4-address  for  the  configured  VLAN  interface  can  either  be  done 
automatically via DHCP or by filling out the boxes "IP-Address" and "Network Mask".   

 

 

 

 

To  ensure  the  correct  function  the  network  appliance  must  be  connected 
with Time Server 8029HEPTA/GPS via the network interface. Furthermore 
it must be ensured that the network appliance is accurately configured with 
the same VLANs. 

 

 

VLAN ID one (1) and two (2) are reserved and are therefore not permitted! 

 

 

 

 

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Reviews:

No comments