hopf 8029HEPTA-V2/GPS Technical Manual Download Page 120

Page: 120 / 130

ACTORY

EFAULTS OF

IME

ERVER

8029HEPTA/GPS

8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00

120 / 130

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

13.2 Factory Default Values of Module 8024GPS (Sync Source)

After triggering a factory default of Module 8024GPS two steps are carried out.

1. Deleting the current leap second information in the GPS receiver

2. Following parameters are set to default values:

Difference time

00h 00min east

Changeover times:

disabled

Begin of Daylight Saving
Time:

Week



first

Day



Monday

Month



January

Hour



End of Daylight Saving
Time:

Week



first

Day



Monday

Month



January

Hour



SyncON / SyncOFF Timeout:

0000

0055

(minutes)

GPS Position:

Longitude:

E 000° 00' 0000

Latitude:

N 00° 00' 0000

GPS reception mode:

Position Fixed

Sync Status OC:

SYNC

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands

hopf 8029HEPTA-V2/GPS, Technical Manual

Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands