hopf 8029HEPTA-V2/GPS Technical Manual Download Page 65

Page: 65 / 130

HTTP/HTTPS

GUI

–

ROWSER

ONFIGURATION

NTERFACE

8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00

65 / 130

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

Time base see also Chapter 14.2.1 Time-Specific Expressions

•

Local time

•

UTC

•

Standard time

•

Standard time with daylight / standard time status

Destination MAC Address

•

09:00:06:03:FF:EF

•

09:00:06:01:FF:EF

•

FF:FF:FF:FF:FF:FF

Synchronization Status based on Starting Transmission (Minimum Accuracy)

This setting defines at which internal accuracy status the SINEC H1 time datagram should be
transmitted (see

Chapter 14.5 Accuracy & NTP Basic Principles

and

Chapter 12 Technical

Data

•

LOW

•

MEDIUM

•

HIGH

The setting Minimum Accuracy = LOW may lead to the output of non-
synchronised (thus possibly wrong) time information.

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands

hopf 8029HEPTA-V2/GPS, Technical Manual

Search results

Summary of Contents for 8029HEPTA-V2/GPS

Reviews:

Related manuals for 8029HEPTA-V2/GPS

Brands by name

Popular brands