hopf 8029HEPTA-V2/GPS Technical Manual Download Page 71 | Manualshive

Page: 71 / 130

background image

HTTP/HTTPS

W

EB

GUI

–

W

EB

B

ROWSER

C

ONFIGURATION

I

NTERFACE

8029HEPTA-V2/GPS GPS - NTP Time Server with LAN Interface - V08.00

71 / 130

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

8.3.3.5 Extended NTP Configuration

NTP is a standard for synchronising clocks in computer systems via packet-based
communication networks. For special applications a NON standard setting can be configured.

For activation of this special NTP setting, the customer's approval shown in the WebGUI
needed to be declared by checking the field "I agree".

8.3.3.5.1 Suppression of unspecified NTP Outputs (Block Output when Stratum

Unspecified)

Unspecified NTP outputs that e.g. are generated by NTP at a restart are suppressed when
this function is enabled.

8.3.3.5.2 NTP Timebase

For custom applications this function enables adjustment of the time base of the NTP output.

Entering this function the transmitted time protocol of the Time Server is not
conform to the NTP standard anymore.
According to the NTP standard NTP uses only the UTC time base. The NTP
time protocol does not allow any leaps in time.

This function is only allowed for the Output of NTP

In case of activated function the output of the Time Server for

SINEC H1 TIME DATAGRAM / TIME / DAYTIME

is released with a wrong time

basis. Therefore this datagram should be deactivated for security reasons.

«
...
69
70
71
72
73
...
»

Summary of Contents for 8029HEPTA-V2/GPS



































































































































Reviews:

No comments

Related manuals for 8029HEPTA-V2/GPS

Brand: RANCHO Pages: 12

Brand: Bosch Pages: 23

Brand: Bosch Pages: 284

Brand: Bosch Pages: 96

Brand: Bosch Pages: 96

Brand: Bosch Pages: 762

plc sw30 - SVGA LCD Projector

Brand: Sanyo Pages: 1

Brand: Sanyo Pages: 40

Brand: Sanyo Pages: 41

Brand: Sanyo Pages: 42

Brand: Sanyo Pages: 42

plc sw30 - SVGA LCD Projector

Brand: Sanyo Pages: 52

Brand: Whirlpool Pages: 10

Brand: Whirlpool Pages: 32

STANDARD CLEANING GAS RANGE

Brand: Whirlpool Pages: 32

Brand: Browning Pages: 2

Brand: Karl Storz Pages: 156

Microcor MWT-3905-MDL

Brand: ROHRBACK COSASCO SYSTEMS Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands